In building, some errors immediately announce themselves. A cracked slab, a wall that isn’t perpendicular, a door that doesn’t close properly. Some lay dormant until something blows up, sets you back or costs you a fortune. Bad gate position is one of those reasons: The second one, that makes a helluva lot more sense. It’s what I call an “on paper” issue — it may seem small in writing, but once a site goes live, the impact can spread throughout a project.
Regardless as to whether the application is residential perimeter fencing, or high security access control, it seems that when people position a gate just about anywhere they feel like it at the time.That’s where difficulties can occur! incorrect gate placement can develop into an issue that no one wants and there seems to be no one making excuses for them later.
Why so many of us end up getting the incorrect gate placement
On the majority of job sites, gates are treated as an afterthought. They follow major structural work behind walls and beneath floors — installation of cantilevers, reinforcing joists, adding new piers and installing beams. That disconnect is one of the major causes of, to borrow a line from Donald Rumsfeld, “unknown unknowns” when it comes to gate placement.
Even if the gate location made sense in design, other real-world circumstances might not cooperate. Slopes shift, utilities blossom where none were expected, traffic patterns migrate, and all of a sudden the path to an easy gate opening becomes inimical to vehicular travel or pedestrian flow. In a situation where such realities are not reconciled in advance of installation, misplacement of gates is virtually unavoidable.
Time presssure is also a factor. In the urgency of a project closure, gates are occasionally erected for convenience, not because they serve any purpose. Building a fence line is faster when the easier place to put an access gate ends up being problematic in eternity.
The impact of incorrect gate placement on daily site works
The true consequence of poor gate placement tends to appear after the project is completed. A gate that swings into a driveway instead of out to street, may technically pass code, but create an experience of daily frustration for the user. The narrow doors can slow deliveries or obstruct the view of drivers, leading to risky moves by vehicles.
For ongoing development projects following initial construction, improper gate positioning interferes with the flow of work. Equipment must follow detour routes and may encounter other issues, emergency access could be blocked or rerouted and temporary workarounds pile up. Individually these issues may not seem dramatic, but they add up to inefficiency and risk.
Safety and liability issues associated with incorrect gate placement
And from a safety perspective, mispositioned gates are more than simply annoying. Gates that swing open towards the public way or shared access can provide a risk of collision. Bad placement can also obstruct sightlines, so that drivers or equipment operators have a harder time seeing people who are moving forward.
Gate liability becomes a real issue if a gate causes an accident. Although the gate, as a structure, may be sound, incorrect placement of the gate is one way to place fault in contractors hands, or in designers’ or property owners’. In many instances it is not a question of whether the gate was constructed properly, but whether or not the placement was thoughtful.”
Residential construction isn’t immune
Homeowners suffer when gate placement isn’t just right, and this is not a problem limited to commercial clients alone. All these are different symptoms of the same underlying societal illness, a side-yard gate that leads to an awkwardly narrow pass-through, perhaps, or the gate in the driveway with not enough clearance for modern cars and trucks or a back-gate put too close inside a backyard where water drainage is problematic.
Improper gate positioning in home construction causes changes made to installed gates. Hinges are re-flipped, panels are trimmed or re-made. They cost more than doing it right in the first place and they nearly always upset the homeowner.
Incorrect gate placement should be addressed at the planning level
Inadequate planning is most often the cause of incorrect gate placement. Gates are not accessories to your land; they’re a working gateway that interacts with people, vehicles and equipment daily.”
Wrong gate placement gets easier to avoid when the builders, the fence workers and those who plan the site communicate early and often. Simple factors — such as how a truck enters the site, or how much swing clearance might be reduced by snow or debris, or even how foot traffic actually flows — can have huge implications for where a gate should go.
Retrofitting Add-on after improper gate installation is costly
Once you have hung a gate in the wrong spot, fixing it can be difficult. Fence lines may need adjustment, concrete footings taken out or automated systems retooled. On larger sites, shifting a gate by even a few feet can set off additional permitting or inspections.
The problem with bad gate installation is that the solution can be more expensive than the original, and avoidable mistake. And by the time the issue becomes apparent, the budget is in a straitjacket and the schedule is etched in stone.
One small thing with grave implications
In construction, details matter. Misplacing gates is a good example of a little thing leading to long-term problems. Gates are used every day. They have more to do with safety, efficiency and user experience than a lot of people realize.
Projects that think about access — not just the structures of it — tend to age better. They need less adjusting, have less complaints and cut liability in the long-term. Not setting the wrong button in turn is not so much a matter of perfect positioning but of premeditation.
Conclusion on mis-positioned gates in construction
The best results in construction come from predicting how spaces will actually be used. When what was intended is significantly different from how things really unfold, the gate is placed in the wrong location. Those two are so in sync up there that, when the gates rise early on, the gates go away here; they just do their job quietly and efficiently.
And in building, that’s just what you want — things to function so effectively nobody else ever thinks about them again.
Read Next: